|
|
Post by DNA RACING on Oct 9, 2011 6:59:16 GMT -7
|
|
|
|
Post by resophonic1 on Oct 11, 2011 5:12:18 GMT -7
Brian,
Is there an official printable registration form on the site, I could not find one.
Updated
*****I used the online registration******
|
|
|
|
Post by DNA RACING on Oct 11, 2011 13:27:29 GMT -7
got them all, thanks guys!! ;D
|
|
|
|
Post by DNA RACING on Oct 16, 2011 6:18:35 GMT -7
|
|
|
|
Post by *5 J's* on Oct 17, 2011 14:42:59 GMT -7
Three Scout-Adult cars shipped today:
Lemon-Lime
Nidhoggr
Team Car
None have had any time on the track - built - set steer - shipped. We'll see...
|
|
|
|
Post by DNA RACING on Oct 17, 2011 17:14:13 GMT -7
Three Scout-Adult cars shipped *** TODAY ***: Lemon-Lime Nidhoggr Team Car None have had any time on the track - built - set steer - shipped. We'll see... if they run anything like your Cabinfever cars did then we got some problems ;D ;D |
|
|
|
Post by johna745 on Oct 17, 2011 17:15:34 GMT -7
|
|
|
|
Post by *5 J's* on Oct 17, 2011 17:22:37 GMT -7
Three Scout-Adult cars shipped *** *** TODAY *** ***: Lemon-Lime Nidhoggr Team Car None have had any time on the track - built - set steer - shipped. We'll see... if they run anything like your Cabinfever cars did then we got some problems ;D ;D It's really a crap shoot. One car, i think Nidhoggr sounded good on the tuning table. Team car sounded like crap. Lemon-Lime so-so. I'm usually better at de-tuniung a car once I get started, so it's probably for the better  It's funny - I just put together a brand new four lane BestTrack w/Microwizard timer for the Cub Scouts - and it's running through the middle of my house - but the cars haven't been on it. Issue is a few joints seem to have a bit of a step up and I didn't want to screw up a wheel. I need to figure out what, if anything, I need to do to the track. |
|
|
|
Post by DNA RACING on Oct 17, 2011 17:28:50 GMT -7
try flipping the lanes around. then if its still there it will be a step down. ;D
|
|
|
|
Post by *5 J's* on Oct 17, 2011 18:08:50 GMT -7
try flipping the lanes around. then if its still there it will be a step down. ;D I think the lane can only go one way - they have an indent on the right side and a ridge on the left - and all the connecting pins are all installed in one end with the other end have the hole to recieve the pins. If you swapped one section around it would be pin to pin. Or is there something I am missing  |
|
|
|
Post by DNA RACING on Oct 17, 2011 18:52:30 GMT -7
you would have to move the pins around, but as long as your moving a whole section the indent should not matter.
|
|
|
|
Post by *5 J's* on Oct 17, 2011 19:00:16 GMT -7
you would have to move the pins around, but as long as your moving a whole section the indent should not matter. correct, it wouldn't really matter which way the indent/bump went if I swapped the entire secion around and like you said - I could swap the pins around to make it work. |
|
|
|
Post by DNA RACING on Oct 17, 2011 19:01:45 GMT -7
swap pins carefully, jiggle alot with a stready pull. i had to do this on my track.
|
|
|
|
Post by *5 J's* on Oct 17, 2011 19:31:06 GMT -7
swap pins carefully, jiggle alot with a stready pull. i had to do this on my track. to correct a step up? or something else? |
|
|
|
Post by DNA RACING on Oct 17, 2011 19:34:31 GMT -7
a step up, i opened the boxes and went wild, never read the directions and had to swap a few sections.
|
|
